Winterize Your Coast Spa with These Easy Steps

If you own a Coast Spa, it’s essential to know how to properly winterize it to avoid any damage from freezing temperatures. Fortunately, winterizing your Coast Spa is a simple and straightforward process that you can easily complete yourself. By following these easy steps, you can protect your spa and ensure that it’s ready for use when warmer weather returns.

The first step in winterizing your Coast Spa is to properly drain it. This involves preparing the drainage area, draining the spa, and cleaning the interior. Once the spa is drained and clean, it’s important to remove any remaining water from the plumbing to avoid any potential damage from freezing temperatures. Finally, it’s essential to take steps to protect your spa from the elements during the winter months.

By following these simple steps, you can protect your Coast Spa from the harsh winter weather and ensure that it’s in good condition when it’s time to use it again. Read on to learn more about each step in the process and how to properly winterize your Coast Spa.

Drain the Spa

One of the most crucial steps in winterizing your Coast Spa is to properly drain the spa. Before draining, make sure to turn off the heater and the pump. This will help prevent any damage to the equipment once the water has been drained. Once you’ve turned off the power, locate the drain valve and attach a garden hose to it. Open the valve and let the water drain completely.

After draining, make sure to remove the filter cartridge and thoroughly clean it. Store the filter in a dry, warm place until you’re ready to use the spa again. In addition to removing the filter, it’s also a good idea to blow out the plumbing lines to remove any remaining water. This will help prevent any freezing and potential damage to the plumbing.

Once all the water has been drained, use a shop vac to remove any remaining water from the bottom of the spa. Make sure to remove all the water, as even a small amount left behind can cause damage. Once you’ve removed all the water, you’re ready to move on to the next step in winterizing your Coast Spa.

Draining your spa may seem like a daunting task, but following these simple steps will help ensure that your spa stays in good condition throughout the winter. Taking the time to properly drain and clean your spa can save you a lot of money and headaches in the long run.

Prepare the Drainage Area

1. Clear the area: Remove any objects that might get in the way of draining water from the spa.

2. Prepare drainage tools: You will need a submersible pump or a siphon to remove water from the spa.

3. Choose the drainage area: Find an area near the spa where the water can flow without causing damage to your property or your neighbor’s property.

Before draining the spa, make sure that the electricity is turned off to avoid any accidents. Once the electricity is turned off, you can begin to drain the water from the spa.

Drain the Spa

The first step to winterizing your Coast spa is to drain the water from it. This is an important step to prevent any damage that can occur due to freezing water. Make sure you have all the necessary tools and supplies before you start the process. You will need a submersible pump, a garden hose, and a clean bucket.

Step 1: Turn off the power to the spa and unplug it. Locate the drainage valve or plug and remove it to drain the water. You can use a submersible pump to speed up the process.

Step 2: Once the water has been drained, use a clean cloth or sponge to wipe any remaining water from the surface. Make sure that the surface is completely dry before moving on to the next step.

Step 3: Inspect the drain plug and gasket for any damage. Replace them if necessary. You don’t want any water to leak back into the spa when it’s being refilled.

Remember, draining your Coast spa properly is crucial to prevent any damage to your spa during the winter season.

Clean the Spa

Once you’ve drained your Coast Spa, it’s time to give it a thorough cleaning. Start by removing any debris that may have accumulated in the spa. Use a skimmer net to remove leaves, insects, and other debris from the surface of the water.

Next, clean the spa’s interior by using a spa surface cleaner. Be sure to follow the manufacturer’s instructions for the specific cleaner you choose. Some cleaners may require dilution, while others may need to sit for a period of time before being rinsed away.

After cleaning the interior of the spa, it’s important to clean the spa cover as well. Use a mild cleaner and warm water to clean the cover, and be sure to rinse it thoroughly.

Scrub the Interior

Use the Right Cleaning Products: It is essential to use the appropriate cleaning products to avoid damaging the spa’s surface. Use a mild cleaning solution to clean the interior surfaces of the spa. Avoid using harsh chemicals, including bleach or scouring pads.

Start Scrubbing: Using a non-abrasive sponge or cloth, scrub the spa’s interior surfaces to remove any dirt, grime, or other residue. Pay particular attention to the areas around the jets and other hard-to-reach areas where bacteria and other microorganisms may accumulate.

Rinse Thoroughly: After scrubbing, rinse the spa’s interior surfaces thoroughly with clean water. Make sure there is no remaining soap residue. Soap residue can cause foam or cloudiness in the water and make it difficult to maintain the spa’s chemical balance.

Remove the Water from the Plumbing

Step 1: Turn off the power to the spa at the circuit breaker. This will prevent the pump from running while the plumbing is being drained.

Step 2: Locate the drain valve at the bottom of the spa. Attach a garden hose to the valve and run the hose to a suitable drainage area.

Step 3: Open the drain valve and let the water drain from the spa. Be sure to open all of the air valves to allow air into the plumbing and help the water drain faster.

Step 4: Blow out the plumbing lines using a wet/dry shop vac or an air compressor. This will help remove any remaining water from the lines and prevent freezing.

Step 5: Add antifreeze to the plumbing lines to protect them from freezing. Follow the manufacturer’s instructions for the amount of antifreeze to use.

Use a Wet Vacuum to Remove Water

Disconnect the Power Supply: Before starting to work on removing the water from the plumbing, make sure to disconnect the power supply to the spa. This will ensure your safety while working with electrical components near water.

Attach the Hose: Attach a hose to the wet vacuum and run it out of the house or to a suitable drainage area. Make sure the hose is long enough to reach the plumbing inside the spa.

Start the Vacuum: Turn on the wet vacuum and let it suck out the water from the plumbing. Start from the lowest point in the spa and work your way up to the highest point, making sure to get all the water out.

Check for Remaining Water: Once you’ve removed all the water with the wet vacuum, check for any remaining water by using a dry towel or a sponge to soak up any excess moisture. Make sure to dry any areas thoroughly to prevent mold or mildew growth.

Reconnect the Power Supply: After you’ve completed the task, it’s time to reconnect the power supply and get ready for the next step in winterizing your coast spa.

Purge the Water from the Jets

Step 1: Turn on the blower motor for 30 seconds to force out any excess water from the jets.

Step 2: Remove the jet covers and use a wet-dry vacuum to remove any remaining water from each jet.

Step 3: Use a pipe cleaner or cotton swab to clean each jet orifice to remove any debris or buildup that may have accumulated.

Step 4: Once all jets have been purged and cleaned, replace the jet covers.

Step 5: If your spa has an air blower system, turn on the blower motor for an additional 30 seconds to purge any remaining water from the air channels.

These steps will ensure that your spa’s jets are thoroughly cleaned and free of any water or debris, preventing potential damage during the winter months.

Blow Out Remaining Water with Compressed Air

After completing the draining process of your home’s plumbing system, the next step is to remove any remaining water using compressed air. This step ensures that no excess water is left in the pipes that could potentially freeze and cause damage to your plumbing system. Before starting the process, make sure you have the necessary equipment, including a compressor, an air hose, and safety goggles.

The first thing you need to do is attach the air hose to the compressor and ensure that it is properly secured. Turn on the compressor and set the pressure to 60 pounds per square inch (PSI). Starting with the highest faucet in your home, slowly open the hot and cold taps until the water is completely drained. Be sure to do this for each faucet, including the outdoor hose bibs, toilets, and showers.

Once all the water has drained, go back to the highest faucet and turn it off. Next, go to the lowest faucet in your home and turn it on. Starting from the highest faucet, attach the air hose to each faucet and blow out the remaining water from each fixture. Keep the compressor running until you’ve blown air through all of the fixtures in your home.

• After blowing out each faucet, close the valve on the faucet.
• Open the next faucet at the highest point in your home and repeat the process until you’ve blown air through all of the fixtures in your home.
• Once you’ve finished blowing out the water, remove the air hose from each faucet and turn off the compressor.

It’s essential to make sure that all the water is removed from the plumbing system before winter sets in. Failing to do so can cause extensive damage to your plumbing system, leading to costly repairs. Blowing out remaining water with compressed air is an effective way to ensure that your plumbing system is winter-ready.

Equipment Needed	Materials Needed	Safety Gear
Compressor	Air Hose	Safety Goggles
Air Hose
	Teflon Tape
		Ear Protection

Protect the Spa

Once you’ve finished draining and blowing out your hot tub for the winter, it’s important to take some measures to protect it from the elements. The harsh winter weather can be damaging to your spa, and taking steps to protect it will help prolong its life. Covering your spa is the first line of defense against snow and ice, and it also helps keep debris from blowing in. Be sure to invest in a high-quality spa cover that fits securely and is made to withstand the winter weather.

Another important step in protecting your spa is to make sure it’s winterized properly. This means removing all of the water from the pipes and equipment to prevent freezing and damage. Additionally, adding a winterizing chemical treatment can help protect the spa’s surfaces from stains and mineral buildup. Be sure to follow the manufacturer’s instructions carefully to ensure you’re using the right products and methods.

Finally, if you live in an area with heavy snowfall, it’s a good idea to create a snow removal plan for your spa. Snow and ice buildup can put stress on your spa cover and potentially damage it. You can use a snow rake or broom to carefully remove snow from the cover, or consider hiring a professional snow removal service to help you out. Taking these steps to protect your spa during the winter months will help ensure it’s ready to use when the weather warms up.

Loosen Fittings and Valves

Before you begin draining your hot tub, it’s important to turn off the power and loosen any fittings and valves to allow the water to flow out freely. If the fittings are too tight, you may have difficulty draining the water completely, which can lead to damage caused by freezing water in the pipes and equipment. Use a wrench or pliers to gently loosen any fittings and valves that may be in the way.

When loosening the fittings and valves, be sure to have a bucket or other container ready to catch any water that may leak out. This will help prevent water damage to your hot tub and the surrounding area. You may also want to consider using a wet/dry vacuum to remove any remaining water from the hot tub and pipes.

After the water has drained completely, it’s a good idea to re-tighten the fittings and valves to prevent any air from entering the system. This can help prevent damage caused by freezing water and also helps ensure that the hot tub is ready to use when you’re ready to start using it again.

Apply Lubricant to Threads and O-Rings

If you want to ensure that your spa stays in excellent condition for years to come, it’s essential to apply lubricant to the threads and O-rings of the fittings and valves. This is a simple process that can be completed in just a few minutes, but it can make a significant difference in the longevity of your spa.

Before you start, make sure you have the right type of lubricant for your spa. Look for a silicone-based lubricant that is safe to use with all types of spa equipment. Applying the wrong type of lubricant can damage your spa and cause costly repairs.

Start by turning off the power to your spa and removing the cover. Locate the fittings and valves that need lubrication, and use a wrench to loosen them. Once the fittings and valves are loose, remove them and apply a small amount of lubricant to the threads and O-rings. Be sure to apply enough lubricant to create a smooth, even coat, but don’t overdo it.

• Tip: Use a small brush or cotton swab to apply the lubricant to hard-to-reach areas.
• Tip: Avoid using petroleum-based lubricants, as they can cause damage to spa equipment over time.
• Tip: Regularly lubricating the fittings and valves of your spa can help prevent leaks and prolong the life of your spa.

Once you have applied the lubricant, use a wrench to tighten the fittings and valves back into place. Be careful not to over-tighten them, as this can damage the threads and O-rings.

After you have tightened all of the fittings and valves, turn the power back on to your spa and let it run for a few minutes to ensure that everything is working correctly. You can then replace the cover and enjoy your spa knowing that you have taken steps to protect it and extend its lifespan.

Use a Spa Cover to Protect the Spa

After completing the winterization process, you should use a high-quality spa cover to protect your spa from external elements such as rain, snow, and debris. Moisture, leaves, and snow can all cause damage to the spa, especially if left unchecked for an extended period.

Make sure that the spa cover fits securely over the spa and is free of any tears or holes. If the cover is damaged or doesn’t fit properly, it won’t provide adequate protection for your spa. You may want to consider investing in a new cover if your current one is old or worn.

Remember to check the spa cover periodically throughout the winter to ensure that it’s still securely in place and free of any damage. A properly fitting and maintained cover will help keep your spa in good condition and ready for use when the weather warms up. Proper maintenance, including covering the spa, can help extend the life of your spa and save you money in the long run.

Store the Accessories

Once the spa is clean and the cover is in place, it’s time to take care of the accessories. This includes items like the steps, handrails, and any additional items you may have used during the cleaning process. Make sure to thoroughly clean these items before storing them away. Use a mild detergent and a soft cloth or sponge to wipe down the surfaces. Rinse with water and dry completely before storing away.

When it comes to storing your spa accessories, there are a few things to keep in mind. First, make sure the items are completely dry before storing them. Any leftover moisture can lead to mold or mildew growth, which can damage the items. Store the items in a cool, dry place away from direct sunlight. This will help prevent fading and damage from UV rays.

It’s also a good idea to keep the accessories organized and easily accessible. Consider using storage containers or hooks to keep everything in its place. This will make it easier to find what you need the next time you’re ready to use your spa.

Remember, taking care of your spa and its accessories is important to ensure that they last as long as possible. With regular maintenance and cleaning, you can enjoy your spa for years to come.

Clean and Dry Accessories

Before storing your spa accessories, it is important to clean and dry them thoroughly to prevent mold and mildew growth. Use a mild soap and warm water to clean any plastic or rubber accessories, and wipe them dry with a clean cloth.

If your spa cover is dirty or stained, use a cover cleaner specifically designed for spa covers. Avoid using harsh chemicals or abrasive cleaners that could damage the cover material.

If you have any fabric accessories, such as towels or robes, be sure to wash and dry them according to their care instructions before storing them.

Frequently Asked Questions