Learn How To Drain Your Evolution Spa In 4 Simple Steps

Are you wondering how to drain your Evolution Spa properly? Whether you’re performing routine maintenance or winterizing your spa, knowing how to drain it is essential. Draining your spa regularly can prevent damage to the equipment and maintain clean water.

In this guide, we will teach you how to drain your Evolution Spa in 4 simple steps. We’ll go through each step in detail to ensure you understand how to complete the process properly. By following these simple steps, you’ll be able to drain your spa without the help of a professional.

Don’t let the fear of draining your spa stop you from enjoying its benefits. With our guide, you can confidently complete the process in no time. Keep reading to learn more!

Step 1: Gather Necessary Tools

Before you start draining your Evolution Spa, it’s important to gather all the necessary tools. Here are some of the things you’ll need:

A garden hose: This will be used to drain the water from your spa.

A submersible pump: If your spa is located below the level of the drain, you will need a submersible pump to drain the water.

A pair of pliers: These will be used to disconnect the drain cap from the bottom of your spa.

Make sure you have all the necessary tools before you start draining your spa. This will make the process much smoother and faster. Once you have all the tools, you can move on to the next step.

Step 1: Gather Necessary Tools

Get the Right Tools for the Job

Before you start draining your Evolution spa, you need to ensure that you have all the necessary tools to make the process as easy and efficient as possible. Make sure to gather the following tools before beginning:

1. A garden hose – You’ll need a garden hose to attach to the drain valve on your spa and direct the water to an appropriate drainage area.
2. A screwdriver – You’ll need a screwdriver to open the drain valve on your spa.
3. A cleaning solution – It’s a good idea to clean the spa shell and plumbing while draining the water, so make sure to have a suitable cleaning solution on hand.

Make sure that you have all of these tools before you begin, as this will save you time and effort in the long run.

Step 2: Turn Off Power

Before beginning to drain your Evolution Spa, it is crucial to make sure that the power is off. This step will ensure that you do not get electrocuted and that the spa does not turn on while you are working on it.

To turn off the power, locate the circuit breaker or disconnect switch near the spa. Turn off the power by flipping the switch or circuit breaker.

It is important to ensure that the power is turned off at the main breaker and not just at the spa breaker. This step will prevent any accidents from occurring.

If you are unsure of how to turn off the power, consult the user manual or contact a professional electrician.

Switch off the Circuit Breaker

Locate your spa’s circuit breaker, which is typically found on the main electrical panel of your home.

Flip the circuit breaker to the “off” position. This will cut off the power supply to your spa and ensure that it’s safe to work on.

Make sure that everyone in your home knows that you are working on the spa and that they should not attempt to turn it on until you have finished draining and refilling the system.

Turn Off the Power to the Spa

• Locate the Power Switch: The power switch for your Evolution spa is typically located near the control panel, which is usually at the top of the spa.

• Switch Off the Power: Once you have located the power switch, turn it off by pushing the button or flipping the switch. This will shut off power to the entire spa.

• Confirm the Power is Off: Double-check to make sure the power is off by checking the control panel and making sure there are no lights or indicators lit up.

Before moving on to the next step, ensure that the power is completely off to avoid any accidents or injuries during the draining process.

Double Check the Power is Off

Before proceeding, double check that the power is indeed turned off. This is a critical step in ensuring your safety and the safety of others who may be assisting you. Check that the spa controls are off and the breaker is switched to the “off” position.

For added security, use a voltage tester to check that the electricity is off. Insert the probes into the power supply to check for any remaining voltage. If the voltage tester indicates there is still power running through the system, do not proceed with the draining process until you have resolved the issue.

It’s better to be safe than sorry when it comes to working with electrical systems. Take the extra time to double check that everything is turned off and there is no remaining voltage before moving on to the next step.

Step 3: Open Drain Valve

Now that the power is off, you can begin the process of draining your spa. The first step is to locate the drain valve. It is usually located at the bottom of the spa and can be easily found by looking for a small spigot.

Once you have located the drain valve, use your pliers to turn the valve counterclockwise. This will open the valve and allow water to begin draining from the spa. You may need to remove the drain cap first, depending on the type of spa you have.

Keep in mind that the water will start to flow out of the spa quickly once the valve is opened. Make sure you have your hose in place to direct the water to the desired location.

As the spa drains, it’s important to keep an eye on the water level. If you notice the water level dropping too low, turn off the drain valve to avoid damaging the spa’s pumps and heater.

Locate the Drain Valve

Before opening the drain valve, locate where it is first. Typically, it can be found near the bottom of the spa or at the back. The valve is usually small, and it may be a different color than the other parts of the spa.

It is important to make sure that the drain valve is open before continuing. Failing to do so can result in damage to the spa, which can be expensive to repair.

Once the valve has been located, check to see if there is any debris or other materials obstructing it. If there is, clear it out of the way to ensure that the water can flow freely.

Connect a Hose to the Drain Valve

Once you have located the drain valve, you will need to connect a hose to it. Make sure you have a hose that is long enough to reach a suitable drain or location to discharge the water.

Attach one end of the hose to the drain valve and make sure it is secure. The other end of the hose should be placed in a location where the water can drain safely, such as a nearby drain or outside area.

Be sure to double-check that the hose is tightly attached to the drain valve, and that the other end is securely positioned to prevent any leaks or spills.

Step 4: Flush The System

Open the Air Relief Valve: Located at the top of the filter, open the air relief valve to release any trapped air. This will prevent any damage to the filter system when you begin to drain it.

Turn on the Pump: Turn on the pump to allow water to flow through the system. Make sure the valve is open so that water flows freely through the system.

Open Each Valve: One by one, open each valve in the system. This will allow water to flow out of each line and clear any debris or dirt that may have accumulated.

Flush the Lines: Using a garden hose, flush the lines with clean water to remove any remaining debris or dirt. This will help prevent clogs and keep the system running smoothly.

Close the Valves and Air Relief Valve: Once you have flushed the lines, close each valve and the air relief valve. This will prevent any air from entering the system and keep the water flowing smoothly.

Refill and Drain Once More

Step 1: Turn off the drain valve and disconnect the hose.

Step 2: Turn on the water supply and fill the spa with water, making sure that it reaches the appropriate level.

Step 3: Turn on the power to the spa and let it run for about 10 minutes.

Step 4: Turn off the power and drain the water from the spa once more. This step will help to remove any remaining debris or contaminants that were stirred up during the flushing process.

Step 5: Once the spa is drained, you can refill it with fresh water and resume normal use.

Remove Any Remaining Water

Use a Wet Vacuum: If there is still water left in the spa, use a wet vacuum to remove it. Be sure to follow the manufacturer’s instructions for using the wet vacuum properly.

Use a Sponge or Cloth: If there is only a small amount of water remaining, you can use a sponge or cloth to soak up the water. Wring out the sponge or cloth into a bucket to dispose of the water.

Use a Submersible Pump: For larger amounts of water, you can use a submersible pump to remove it. Place the pump in the water and follow the manufacturer’s instructions for pumping the water out of the spa.

Check for Any Remaining Water: Once you have removed the water, double-check to make sure that there is no water left in the spa. If there is still water present, repeat the process of removing the water until the spa is completely dry.

Additional Tips for Draining Your Spa

Clean the Spa Before Draining: It’s a good idea to clean your spa before you drain it. This way, you can remove any dirt or debris that may be in the water.

Use a Wet/Dry Vacuum: You can use a wet/dry vacuum to remove any remaining water from the spa. This is a great way to ensure that there is no water left in the pipes.

Leave the Drain Open: After you have drained the spa, it’s a good idea to leave the drain open. This will allow any remaining water to evaporate.

Refill Your Spa: After you have drained your spa, it’s important to refill it with fresh water. Make sure you follow the manufacturer’s instructions for refilling your spa.

Consider Professional Help: If you are unsure about how to drain your spa or if you encounter any problems, it’s best to call a professional. They can help you ensure that your spa is properly drained and ready for use.

Check Your Owner’s Manual First

If you have an owner’s manual, always check it first for specific instructions on how to drain your spa. This will give you the most accurate information and ensure that you don’t damage your spa.

Follow the instructions in the manual carefully and make sure you have all the necessary tools and equipment before you begin.

If you can’t find your manual or it’s outdated, check the manufacturer’s website for a digital version or contact them directly for assistance.

Frequently Asked Questions