How To Install Passion Spa Jets: Step-by-Step Guide

Are you a hot tub owner looking to improve your spa experience? Adding new jets to your Passion Spa can make all the difference. But how can you install them without damaging your spa? In this step-by-step guide, we will show you how to install Passion Spa jets easily and effectively. With our guide, you’ll be able to enjoy a rejuvenating and relaxing spa experience in no time.

Before we get started, it’s essential to gather all the necessary tools and materials for the installation process. Having the right equipment will make the process much smoother and easier. Once you have everything, it’s time to locate the access panel and remove the old jets.

Don’t worry if you’re not familiar with plumbing or DIY projects; we’ll guide you through the process. By following our step-by-step guide, you’ll be able to connect the jets to the plumbing system and test them for optimal performance. So, let’s get started with the installation process and upgrade your Passion Spa to a whole new level.

Read on to discover our expert tips and tricks to install Passion Spa jets successfully. Trust us, you don’t want to miss this valuable information!

Gather Necessary Tools and Materials

To install Passion Spa jets, you will need to gather a few tools and materials. First, you will need a wrench, a screwdriver, and a pair of pliers. Additionally, you will need silicone sealant, a replacement jet kit, and Teflon tape. Make sure that you have all of these items before you begin installing your new jets.

Before you start working on the jets, make sure to turn off the power supply to the hot tub. You can do this by turning off the circuit breaker or disconnecting the power cord. It’s also a good idea to drain the water from your hot tub to make the installation process easier and safer.

Once you have gathered all of the necessary tools and materials and have turned off the power supply to the hot tub, you can begin to install your new Passion Spa jets. The following steps will guide you through the process and help you get your hot tub up and running in no time.

Prepare Safety Equipment

1. Protective Clothing: Wear protective clothing like gloves, goggles, and long sleeves shirts to prevent injuries and protect the skin from chemical exposure.

2. Respirator: Use a respirator mask to prevent inhaling any fumes or debris during the installation process.

3. Fire Extinguisher: Keep a fire extinguisher nearby to prevent any accidental fires that may occur during installation.

4. Electric Testers: Use an electric tester to ensure that there is no electrical current running through the wires before touching them.

5. Drainage System: Ensure that the drainage system is functioning properly and that there is no water in the spa before installation.

6. Assistant: Have an assistant present to help with lifting and moving heavy equipment during the installation process.

Before starting the installation process, make sure to prepare all the necessary safety equipment to prevent injuries and ensure a smooth installation process.

Purchase New Jets and Materials

• Identify the type of jets: Passion Spas offer a variety of jets such as directional, spinning, and cluster. Identify which type of jets you want to replace before purchasing new ones.
• Check the model of the spa: Purchase the jets that are compatible with your spa’s model. This information can be found in the spa’s owner manual or by contacting the manufacturer.
• Buy necessary materials: Purchase materials such as PVC cement, plumbers tape, and silicone sealant. Ensure you have all the necessary materials before beginning the installation process.
• Consider the number of jets: Decide on the number of jets you want to install. This will help you determine how many jets to purchase.

After purchasing the new jets and materials, it’s time to move on to the next step: locating the access panel.

Locate the Access Panel

Step 1: Turn off the power to the spa. This is important for your safety when working on the plumbing and electrical connections.

Step 2: Locate the access panel on the spa. The panel is typically located near the pump and motor area. If you are unsure where it is, check the manufacturer’s instructions.

Step 3: Remove the access panel screws or clips. The panel may be attached with screws, clips or both. Use the appropriate tool to remove them, and place them in a safe place.

Step 4: Gently remove the access panel. Be careful not to damage the panel or any of the wires or pipes behind it.

Step 5: Inspect the area behind the access panel. Check for any damage or leaks in the plumbing or electrical connections. Make sure everything is secure and in good working order before proceeding.

Refer to the User Manual

Before beginning the installation process, make sure to review the user manual provided by the manufacturer for any specific instructions and warnings.

The manual will provide you with important information on how to safely access and remove the old jets, as well as how to properly install and connect the new jets.

It’s important to follow the instructions provided in the manual to ensure the installation is done correctly and safely.

If you have any questions or concerns while following the manual, don’t hesitate to reach out to the manufacturer’s customer service for assistance.

By referring to the user manual, you can avoid any potential mistakes and ensure a successful installation process.

Remove Old Jets

Step 1: Turn off the Power

Make sure to turn off the power to your spa before starting any work. This is to ensure your safety and prevent any electrical hazards.

Step 2: Remove the Access Panel

Locate the access panel and remove it to access the old jets. Make sure to keep all screws and bolts in a safe place to avoid losing them.

Step 3: Remove the Old Jets

Use a wrench to unscrew the old jets from the spa. Make sure to keep all parts together and organized for easy installation of the new jets later.

Use a Jet Wrench Tool

Step 1: Before using the jet wrench tool, turn off the power supply to the spa to prevent any accidents from occurring.

Step 2: Locate the jet that you need to remove and use the jet wrench tool to loosen the nut that secures it in place.

Step 3: Once the nut has been loosened, use your hand to unscrew it and remove the old jet from the spa.

Removing old jets can be a challenging task, but using a jet wrench tool makes it easier and safer. Remember to turn off the power supply to the spa and follow these steps to avoid any injuries or damages to your spa.

Install New Jets

Step 1: Insert the new jet into the opening and align it with the holes.

Step 2: Apply a small amount of silicone sealant around the edge of the jet to create a waterproof seal.

Step 3: Insert the retaining ring and tighten it firmly with the jet wrench tool.

Step 4: Repeat this process for all the other jets you want to replace.

Step 5: Once all the new jets have been installed, turn the power back on and test them to ensure they work properly.

By following these simple steps, you can replace the old and damaged spa jets in your Passion Spa with new ones, improving your spa experience and allowing you to relax in style. It is always recommended to refer to the user manual or seek professional help if you encounter any issues during the installation process.

Insert the New Jets into the Jet Housing

Step 1: Place the new jet into the housing, making sure it fits snugly.

Step 2: Tighten the jet collar clockwise by hand until it’s snug, but not too tight.

Step 3: Use a jet wrench tool to tighten the collar a quarter turn clockwise to secure the jet in place.

Step 4: Repeat these steps for each jet until all new jets have been installed.

Once all the new jets have been installed, it’s time to test them out and enjoy a relaxing soak in your Passion Spa!

Tighten the New Jets with Jet Wrench Tool

Use the jet wrench tool to tighten the new jets in place. Make sure the jets are securely fastened but be careful not to over-tighten them.

Hold the jet in place with one hand while turning the wrench tool with the other hand. Use a gentle, steady pressure to tighten the jet. If the jet does not feel secure, turn the wrench tool a little bit more until it is firmly in place.

After tightening all the new jets, double-check each one to ensure it is securely fastened. This will prevent any leaks or damage to the jets over time.

Connect the Jets to Plumbing System

After installing the new jets, it is time to connect them to the plumbing system. First, locate the water supply valve and ensure it is turned off to prevent any water flow.

Next, connect the water pipe to the jet housing using a PVC cement. Make sure the connection is tight and secure.

Finally, turn on the water supply valve and check for any leaks. If there are any leaks, tighten the connections with a wrench tool.

Attach the Jets to the Plumbing System

Position the new jet in the opening and align it with the plumbing system. Use a flashlight to see if the jet is properly aligned.

Apply a layer of sealant around the base of the jet. Make sure that the sealant covers the entire base and creates a tight seal to prevent leaks.

Tighten the jet into the plumbing system using the jet wrench tool. Be careful not to overtighten as this can damage the threads and cause leaks.

Repeat the process for all the other jets, making sure that each one is properly aligned and tightly secured to the plumbing system.

Check for Leaks and Secure the Connections

After attaching the new jets to the plumbing system, turn on the water supply and test the jets to check for any leaks. If there are leaks, turn off the water supply and carefully tighten the connections using a wrench tool.

Once the connections are secure, turn on the water supply again and check for any leaks. If there are no leaks, secure the connections by applying a sealant around the connections. Allow the sealant to dry completely before using the jet system.

It is important to regularly check the connections for any leaks or damage to ensure the jet system is functioning properly and to prevent any potential damage to the plumbing system.

Turn on the Pump and Fill the Spa with Water

Before turning on the pump, ensure that all connections and valves are securely tightened to prevent leaks. Once everything is secured, turn on the pump and fill the spa with water. It is important to fill the spa with water before turning on the pump to prevent damage to the pump.

As the spa is filling up, check for any leaks or drips. If there are any leaks, turn off the pump and tighten the connections again. Once you have confirmed that there are no leaks, continue filling the spa with water.

While the spa is filling, keep an eye on the water level and adjust the water flow if necessary. Once the water level reaches the desired height, turn off the water supply and check the water chemistry levels to ensure they are within the recommended range.

Once the water chemistry levels are balanced, turn on the spa’s heater and allow the water to heat up to the desired temperature. Depending on the size of your spa and the desired temperature, this may take several hours.

Test the Jets

Turn on the jets: Turn on the spa’s jets and observe their performance. Ensure that all the jets are working properly and are producing the desired amount of water flow.

Check for leaks: Inspect the jet connections and plumbing for any leaks or drips. If any leaks are detected, turn off the pump and fix the issue before proceeding.

Adjust the jets: If the jets are not performing as expected, try adjusting them. You can adjust the direction and intensity of the jets by turning the nozzles or using the jet’s control valve.

Monitor water temperature: Keep an eye on the water temperature to ensure that it is within the desired range. Most spas have a maximum temperature of 104 degrees Fahrenheit (40 degrees Celsius).

Enjoy the jets: Once you have tested and adjusted the jets, relax and enjoy the soothing massage they provide.

Turn on the Jets and Observe the Water Flow

Once you’ve filled the spa with water, it’s time to test the jets. Turn on the pump and activate the jets, one by one, starting with the first one. Observe the water flow to ensure that each jet is working properly. Look for signs of weak or inconsistent water flow, which could indicate a clog or other problem.

If you notice any issues with the water flow, turn off the pump and check the jets for clogs or other obstructions. Use a jet wrench tool to remove the jets and clear out any debris that may be causing the problem. Once the clog is cleared, reattach the jet and test the water flow again.

It’s important to test each jet individually, as some jets may have more powerful water flow than others. If you notice any inconsistencies between the jets, you may need to adjust the water flow settings to ensure that each jet is working properly.

Adjust the Jets Direction and Intensity

After observing the water flow, you may need to adjust the direction and intensity of the jets to suit your preferences. The following steps will guide you:

Step 1: Turn off the jets and let the water settle. This will allow you to see the current direction and intensity of the water flow.

Step 2: Identify the jet(s) that need adjustment. Most hot tubs have adjustable jets that can be rotated to change the direction of the water flow. Some also have a dial that controls the intensity of the water flow.

Step 3: Use your hand or a jet tool to adjust the direction of the jet(s). Start by rotating the jet(s) clockwise or counterclockwise to change the direction of the water flow. If you have a dial, turn it to increase or decrease the intensity of the water flow.

Step 4: Turn on the jets again and observe the water flow. If you are satisfied with the direction and intensity of the water flow, you’re done! If not, continue adjusting the jet(s) until you find the perfect settings.

Replace the Access Panel

Make sure the area around the access panel is clear of debris and water to prevent slips and falls. Use a towel to dry any wet spots.

Lift the access panel into place and align it with the mounting brackets. Use a screwdriver to secure the panel to the brackets.

Check the edges of the panel to ensure a tight fit. If there are gaps, use a sealant to prevent water from entering the cabinet.

Test the panel by gently pushing on it to make sure it is securely attached. If it feels loose, re-tighten the screws or adjust the brackets.

Finally, turn on the power to the spa and verify that the jets are working properly. If everything is functioning correctly, your spa is now ready to use!

Align the Access Panel and Secure the Screws

Once you have finished testing the jets and are satisfied with their performance, it’s time to replace the access panel.

Carefully align the panel with the opening and ensure that all of the edges are flush.

Once you are satisfied that the panel is in the correct position, use a screwdriver to secure the screws.

Make sure to tighten the screws evenly to ensure that the panel is held securely in place.

Finally, give the panel a gentle tap to make sure it is securely attached and flush with the surface of the spa.

Turn on the Power and Test the Jets Again

After replacing the access panel, make sure that it is properly aligned and secured with the screws. Once you have done that, you can turn on the power to the spa.

Allow the spa to run for a few minutes and check for any unusual sounds or leaks. Observe the jets to ensure that they are functioning properly and that there is a strong and consistent flow of water. If everything looks good, you can proceed with testing the jets again.

Turn on the jets and adjust their direction and intensity as needed. Make sure that the jets are aligned correctly and that they are producing the desired level of pressure. Observe the water flow and make sure that there are no blockages or other issues affecting the jets.

If everything looks good during this final test, congratulations! You have successfully replaced the access panel and tested the spa jets. Enjoy your newly functioning spa and the relaxing benefits that it provides.

Enjoy Your New Passion Spa Experience

Congratulations! You have successfully installed and tested your Passion Spa. Now, it’s time to sit back, relax and enjoy the ultimate spa experience.

Make sure to keep your spa clean and well-maintained to ensure its longevity and your continued enjoyment. You should regularly check and balance the water chemistry, clean the filter, and drain and refill the water every 3-4 months.

Don’t forget to consider adding accessories to enhance your spa experience. Aromatherapy scents, LED lighting, and a sound system can all add to the ambiance and relaxation of your spa time.

Remember to follow all safety guidelines and precautions when using your spa. Never use the spa alone, and always supervise children and pets. It’s also important to limit your time in the spa to avoid dehydration and overheating.

Thank you for choosing Passion Spas, and we hope you enjoy your new spa for years to come!

Frequently Asked Questions