Deflate Your Lay Z Spa New York in 7 Easy Steps

If you own a Lay Z Spa in New York, you know how much enjoyment it can bring to your outdoor space. However, with summer coming to an end, it’s time to pack up your inflatable hot tub for the season. Deflating your Lay Z Spa might seem like a daunting task, but it’s actually quite simple. In this article, we’ll guide you through the process in seven easy steps so that you can safely store your spa until next year.

Before we get started, it’s important to note that deflating your Lay Z Spa is crucial for its longevity. By properly deflating and storing your spa, you can avoid any potential damage to the material and extend its lifespan. With that said, let’s dive into the seven easy steps to deflate your Lay Z Spa.

Step-by-step guide

Are you ready to take the first step towards deflating your Lay Z Spa in New York? Keep reading to learn how to properly deflate, clean, and store your spa for the winter season.

Step 1: Turn Off the Spa Heater and Unplug

Before deflating your Lay Z Spa New York, make sure the heater is turned off and the power cord is unplugged from the power source. This ensures your safety while you work on the spa. The heater can be damaged if it is still on when you start deflating the spa. To avoid accidents, be sure to unplug the spa from the power source.

Locate the power cord and follow it to the power source. If your spa has a switch, turn it off before unplugging the spa from the power source. For added safety, use a circuit breaker to make sure the power source is turned off. Remember, you cannot be too careful when it comes to your safety.

Once you have unplugged the spa from the power source, remove the cover and place it aside. If your spa is dirty, clean the cover with a soft cloth and mild detergent. Now you are ready to move on to the next step of deflating your Lay Z Spa New York.

1.1 Disconnect the Power Cord from the Outlet

1. Locate the power cord attached to the spa and trace it back to the outlet it is plugged into.

2. Make sure your hands are dry before attempting to unplug the cord to avoid electrocution.

3. Unplug the power cord from the outlet and make sure it is not touching any water.

4. Keep the power cord away from the spa while deflating it to avoid any damage to the cord.

5. Check the power cord for any damage or wear and tear, and replace it if necessary before using the spa again.

6. Store the power cord safely in a dry place away from the spa after deflating it.

It’s important to disconnect the power cord from the outlet before deflating your Lay Z Spa New York to ensure your safety and prevent any damage to the spa or the cord. By following these steps, you can safely unplug and store the power cord until you’re ready to use the spa again.

1.2 Turn Off the Power Switch on the Control Panel

After unplugging the spa, the next step is to turn off the power switch on the control panel. The control panel is usually located near the spa and is where you adjust the temperature, jets, and other features. Find the power switch and turn it to the “off” position to ensure that there is no electrical current running through the spa.

Remember to consult your owner’s manual if you are not sure where the power switch is located. It is important to turn off the power switch to prevent damage to the spa’s internal components and to ensure your safety when releasing the air and water.

Once you have turned off the power switch, you can proceed to the next step of releasing the air from the spa.

Step 2: Remove the Valve Caps and Release the Air

After unplugging the Lay Z Spa New York, it’s time to release the air. Start by removing the valve caps from each of the inflation points. This will allow the air to escape and deflate the spa.

Tip: If you’re having trouble removing the valve caps, try using a pair of pliers to twist them off.

Next, locate the air release valve on the pump unit and unscrew the cap. This will allow any remaining air in the spa to escape. Be sure to keep the air release valve open until all the air has escaped.

Warning: Never use sharp objects to puncture the spa as this can cause irreparable damage.

Once all the air has been released, replace the valve caps and screw the air release valve cap back on. Your Lay Z Spa New York should now be completely deflated and ready for cleaning or storage.

2.1 Remove the Valve Caps from the Inflation Valves

Step 1: Locate the inflation valves on the spa. They are usually located on the top of the spa, near the control panel.

Step 2: Use a valve wrench to unscrew the valve caps from each valve. If you don’t have a valve wrench, you can use a pair of pliers.

Step 3: Once the valve caps are removed, press down on the valve stems to release the air from the spa. You should hear a hissing sound as the air is released.

Note: Be sure to release all of the air from the spa. If you leave any air in the spa, it will be harder to deflate and may cause damage to the spa walls.

2.2 Open the Inflation Valves to Release the Air

Once you’ve removed the valve caps, it’s time to release the air from the Lay Z Spa New York. Locate the inflation valves on the spa and open them up by turning them counterclockwise. This will allow the air to escape and deflate the spa. Be sure to remove any plugs or stoppers from the valves beforehand.

As the spa deflates, you may need to press down on the sides to help push the air out. You can also use a towel or cloth to help push the air out from the edges. Keep an eye on the spa as it deflates to make sure the air is escaping evenly and there are no areas that are still inflated.

Once the spa is fully deflated, turn the inflation valves clockwise to close them up. This will prevent any air from getting back into the spa as you continue to drain the water and clean the interior.

Step 3: Drain the Water from the Spa

Attach a Garden Hose to the Drain Valve

Before draining the water, attach a garden hose to the drain valve located at the bottom of the spa. This will direct the water to a suitable drainage area.

Open the Drain Valve

Once the hose is securely attached, open the drain valve and allow the water to flow out of the spa. This may take some time, depending on the size of the spa and the amount of water in it.

Use a Pump to Speed Up the Draining Process

If you want to speed up the draining process, you can use a pump to help remove the water. Simply connect the pump to the garden hose and turn it on to remove the water quickly.

Clean the Interior of the Spa

While the spa is draining, take the opportunity to clean the interior of the spa using a mild detergent and a soft cloth. This will help remove any dirt or debris that may have accumulated.

Rinse the Spa with Clean Water

After cleaning, rinse the spa with clean water to remove any remaining soap residue. This is important to prevent any potential damage to the spa’s material. Once rinsed, turn off the hose and let the spa continue to drain until it is completely empty.

3.1 Attach a Garden Hose to the Drain Valve

Locate the drain valve on the outside of the spa and remove the cap. It is typically located at the bottom of the spa near the control panel. Attach a garden hose to the drain valve and make sure it is securely fastened.

Open the drain valve and let the water drain out. You can use a submersible pump to speed up the process. Make sure the other end of the garden hose is in a location where the water can drain freely, such as a nearby drain or outside area.

Keep an eye on the water level and turn off the drain valve when the water is below the recommended level. Do not let the spa completely drain, as this can cause damage to the pump and other components.

Step 4: Clean the Interior of the Spa

Drain Remaining Water: After draining most of the water from the spa, use a wet-dry vacuum to remove any remaining water from the bottom.

Apply Cleaner: Apply a non-abrasive cleaner to the interior of the spa. Avoid using abrasive cleaners, which can damage the surface of the spa.

Scrub: Scrub the interior of the spa with a soft cloth or sponge to remove any dirt or grime. Be thorough but gentle to avoid damaging the spa’s surface.

Rinse: Rinse the interior of the spa thoroughly with water to remove any remaining cleaner and dirt.

Dry: Use a clean, dry cloth or towel to dry the interior of the spa. Make sure the spa is completely dry before refilling with water to prevent mold or mildew from developing.

4.1 Use a Soft Cloth to Clean the Interior of the Spa

Start by filling a bucket with warm water and add a small amount of mild soap. Using a soft cloth or sponge, gently wipe down the interior of the spa, focusing on any areas that appear dirty or stained. Avoid using any harsh or abrasive cleaners as these can damage the surface of the spa.

For tough stains or buildup, you can use a non-abrasive cleaner specifically designed for spas. Be sure to follow the manufacturer’s instructions and rinse the spa thoroughly after cleaning.

Take care not to scratch or damage any of the fittings or surfaces inside the spa while cleaning. It’s important to maintain the integrity of the spa’s interior to ensure its longevity and performance.

After cleaning, rinse the interior of the spa thoroughly with clean water to remove any soap residue. Once the spa is clean and rinsed, it’s ready to be refilled and enjoyed.

Regular cleaning of the interior of your spa can help prevent the buildup of dirt and debris, and keep the water looking and feeling fresh. It’s recommended to clean the interior of the spa every 3-4 months, or as needed based on usage.

4.2 Rinse the Interior of the Spa with Clean Water

After cleaning the interior of the spa, it’s important to rinse it thoroughly with clean water. This will remove any remaining cleaning agents or dirt. Use a hose with a nozzle attachment to spray down the walls and floor of the spa. Pay close attention to the jets and other hard-to-reach areas to ensure that all debris is removed.

If you notice any stubborn stains, you can use a soft-bristled brush to gently scrub the affected area. Be sure to rinse the area thoroughly afterwards to remove any debris.

Once you’ve finished rinsing the spa, use a clean, dry towel or cloth to wipe down the interior. This will help to remove any excess water and prevent water spots from forming.

Remember, keeping your spa clean will help to extend its lifespan and ensure that it continues to operate at optimal levels.

Next, you can move on to refilling your spa with fresh water and getting it ready for use again.

4.3 Dry the Interior of the Spa with a Towel

Step 1: Start by using a clean and dry towel to wipe down the interior of the spa. Be sure to get into all the nooks and crannies, including the seats and corners.

Step 2: Once you’ve wiped down the entire interior, use a second dry towel to go over it again and make sure it’s completely dry.

Step 3: Pay special attention to any areas that may be prone to moisture buildup, such as around the jets or the waterline. These areas should be thoroughly dried to prevent mold or mildew from forming.

Step 4: If you notice any stubborn stains or buildup that won’t come off with a towel alone, you may need to use a spa cleaner or degreaser to remove them. Be sure to follow the manufacturer’s instructions carefully.

Step 5: Finally, once the interior is completely dry and clean, you can replace the spa cover and get ready to enjoy your freshly cleaned hot tub!

Step 5: Remove the Filters and Clean Them

Turn off the power to the spa. Before removing the filters, make sure to turn off the power to the spa to avoid any accidents.

Locate and remove the filters. The filters are usually located in a compartment near the spa’s pump. Remove the compartment cover and carefully take out the filters.

Rinse the filters with a garden hose. Use a garden hose to rinse off any debris or dirt that has accumulated on the filters. Make sure to rinse both the inside and outside of the filters.

Soak the filters in a filter cleaner solution. Fill a bucket with water and add a filter cleaner solution to it. Soak the filters in the solution for a few hours to remove any remaining dirt or debris. Rinse the filters thoroughly with clean water and let them dry completely before putting them back in the spa.

5.1 Locate the Filter Housing and Remove the Lid

The filter housing is usually located near the pump and heater assembly. It may be attached to the spa shell or mounted on a nearby wall. Once you’ve found it, turn off the power to the spa and remove the lid by loosening the screws or clips that hold it in place.

Caution: Make sure the power is off before removing the lid to avoid the risk of electric shock. If you’re unsure about how to turn off the power, consult the spa’s owner manual or contact a professional.

After removing the lid, inspect the filter for any signs of damage or wear. If you notice any cracks, tears, or other defects, it may be time to replace the filter.

5.2 Remove the Filters from the Filter Housing

Step 1: Once you have located the filter housing, carefully remove the lid and set it aside.

Step 2: Look for the filters inside the housing. Depending on the model of your spa, there may be one or more filters to remove. Pull the filters out of the housing.

Step 3: Inspect the filters for any signs of damage or wear and tear. If the filters are in good condition, proceed with cleaning. If they are damaged, it may be necessary to replace them with new ones.

Step 4: Rinse the filters thoroughly with clean water to remove any debris or dirt. You can use a hose or a sink for this task.

Frequently Asked Questions