Deflate Your Coleman Lazy Spa in 5 Simple Steps

Are you looking for an easy way to deflate your Coleman Lazy Spa? Look no further! With just five simple steps, you can easily deflate your spa and store it away until your next use.

Whether you’re packing up for the winter or simply moving your spa to a new location, knowing how to properly deflate it is essential. It can be frustrating to try and figure it out on your own, but with these easy steps, you’ll be able to deflate your spa quickly and easily.

Before you get started, make sure you have all the necessary supplies on hand. You’ll need a few things to get the job done right, including a pump, a hose, and some towels. Don’t have these items? No problem! We’ll walk you through each step and provide tips along the way.

So, let’s get started and learn how to deflate your Coleman Lazy Spa in just five simple steps. You’ll be surprised at how easy it is!

Step 1: Gather Your Supplies

Gathering the right supplies is essential to successfully deflating your Coleman Lazy Spa. To get started, gather the following items:

A Pump – To ensure you remove all of the air from the spa, you’ll need a powerful pump that can handle the job. You can find such a pump at most outdoor or hardware stores.

A Hose – The pump needs a hose to attach to the inflation valve on the spa. A standard garden hose should do the trick, just make sure it’s long enough to reach.

A Flat Surface – To prevent any damage to your spa, it’s important to deflate it on a flat surface. This will ensure that the air is evenly distributed throughout the spa.

A Friend – While this step can technically be done solo, it’s much easier with a helping hand. Grab a friend to assist you in moving the spa and holding the hose in place while the air is being removed.

A Container – When the spa is fully deflated, there will be some residual water left inside. It’s important to have a container on hand to collect this water to prevent any messes.

Tools You’ll Need

1. Air Pump: You’ll need an air pump to inflate and deflate your Coleman Lazy Spa. Make sure it’s compatible with your spa’s inflation valve.

2. Pressure Gauge: It’s important to have a pressure gauge to accurately measure the air pressure in your spa. This will prevent over-inflation or under-inflation, which can damage your spa.

3. Clean Towels: To ensure that your spa stays clean and dry during the deflation process, have a few clean towels ready to wipe down any excess water or debris that may have accumulated.

Having the right tools on hand will make the deflation process quick and easy. With an air pump, pressure gauge, and clean towels, you’ll be able to safely deflate your Coleman Lazy Spa without damaging it.

Clean Your Spa

Before you begin to deflate your spa, it’s important to clean it properly. This will help prevent any dirt or debris from getting inside the spa during the deflation process. Use a mild soap and a soft sponge to clean the sides of the spa. Be sure to also clean the air nozzles and inflation valve to prevent any dirt or debris from getting inside the spa during the deflation process.

After you’ve finished cleaning your spa, be sure to dry it off completely before deflating it. This will help prevent any water from getting inside the spa and potentially causing damage. You can use a towel to dry off the sides and bottom of the spa, and use a hairdryer on a low heat setting to dry off the air nozzles and inflation valve.

If you notice any minor damage to your spa during the cleaning process, such as a small puncture or tear, it’s important to take care of it before deflating the spa. You can use a vinyl repair kit to patch up any small holes or tears in the spa before proceeding with deflation.

Locate the Inflation Valve

Before you can start deflating your Coleman Lazy Spa, you will need to locate the inflation valve. The valve is typically located on the side of the spa and can be identified by its round shape with a small tab or knob. Make sure that your spa is completely unplugged before you start.

It is essential to find the inflation valve because this is where the air will come out when you start deflating your spa. You should also ensure that you have a clear path around the spa to allow the air to escape without obstruction.

If you are having trouble locating the inflation valve, refer to the user manual that came with your Coleman Lazy Spa. The manual will provide a diagram that shows the location of the valve.

Step 2: Remove the Spa Cover

The first step in deflating your Coleman Lazy Spa is to remove the cover. The cover is secured with straps or buckles that need to be undone. Once you have released the straps or buckles, remove the cover and set it aside.

Important: Before removing the cover, make sure it is completely dry to prevent mold or mildew growth.

If your spa has an inflatable lid, make sure to deflate it as well. Locate the valve on the lid and use the air pump to deflate it. Once the lid is deflated, remove it and set it aside with the cover.

Tip: It’s a good idea to clean the cover and lid before storing them. Use a mild soap and water to clean the surface and then let them dry completely before storing them.

Secure the Cover Straps

After removing the cover from your spa, it’s important to secure the cover straps to prevent them from getting in the way during deflation. Locate the cover straps and use them to secure the cover to the side of the spa.

Tip: Make sure to secure the straps tightly so they don’t come loose during the deflation process.

Once the straps are secured, you can move on to the next step of deflating your Coleman Lazy Spa.

Remove the Cover

• Unclip the straps: Starting at one end of the spa, locate the cover clips and unclip them. Work your way around the spa, unclipping all the clips.

• Remove the cover: Once all the clips are undone, you can gently remove the cover from the spa. Fold it up and set it aside in a dry, clean place.

• Inspect the cover: Before storing the cover, inspect it for any signs of wear and tear. If you notice any damage, it may be time to replace it with a new one.

Removing the cover is an important step in deflating your Coleman Lazy Spa. By following these simple instructions, you can ensure that your cover stays in good condition and your spa stays clean and protected until the next time you use it.

Step 3: Open the Inflation Valve

Remove the Cap

The inflation valve is covered with a cap. Remove the cap from the valve, but be sure not to lose it.

Push the Valve In

The valve is spring-loaded and must be pushed in to let air out of the spa. Press down on the valve and hold it in place.

Turn the Valve Counter-Clockwise

While holding the valve in, turn it counter-clockwise to release the air from the spa. Make sure you don’t turn it too far or the valve could come loose.

Wait for the Air to Release

Depending on how much air is in the spa, it may take a few minutes for all the air to be released. You can speed up the process by pushing down on the sides of the spa to force the air out.

Close the Valve

Once all the air is out of the spa, turn the valve clockwise to close it. Make sure it is securely in place.

Release the Valve Cap

Before you can inflate the spa, you need to release the valve cap. Use a flathead screwdriver or a coin to turn the cap counterclockwise until it pops off.

Be careful not to lose the cap! It is small and can be easily misplaced. You can set it aside in a safe place while you inflate the spa.

If the cap is stuck, you can try using a pair of pliers to help turn it. However, be careful not to overtighten the cap when you put it back on.

Attach the Pump Hose

The next step is to attach the pump hose to the inflation valve. Make sure the hose fits snugly over the valve to avoid any leaks.

Check the user manual or manufacturer’s instructions to ensure you’re using the correct hose for your inflatable spa.

Once the hose is securely attached, turn on the pump and let it inflate the spa. Keep an eye on the pressure gauge to ensure the spa is inflating properly and not overinflating.

Step 4: Push Out the Air

Turn on the Pump: After attaching the hose, turn on the pump to start the deflation process. Make sure the hose is securely attached to the valve and the pump is on a stable surface.

Monitor the Deflation: Keep an eye on the spa as it deflates to ensure that it is deflating evenly. Use your hands to smooth out any wrinkles or folds that may be preventing air from escaping.

Use a Vacuum: If you have trouble getting all the air out of the spa, try using a vacuum cleaner to suck out the remaining air. Attach the vacuum hose to the valve and turn on the vacuum.

Roll the Spa: Once most of the air is out, start rolling the spa towards the valve end. This will push the remaining air towards the valve, making it easier to remove.

Close the Valve: Once all the air has been removed, close the valve by turning the cap clockwise. Ensure that the cap is tight to prevent any air from getting in or out of the spa during storage.

Start at the Opposite End

When pushing out the air, it’s important to start at the opposite end of the spa from the inflation valve. This will ensure that all of the air is pushed out and that there are no pockets of air left in the spa.

Use your hand to push down on the cover as you move towards the inflation valve. This will force the air out through the valve and into the pump hose.

Continue to push down on the cover until all of the air has been removed. You may need to go over certain areas multiple times to ensure that all of the air is out.

Once all of the air has been removed, you can remove the pump hose from the inflation valve and replace the valve cap. Your spa cover is now ready to be secured back in place.

Remember to always start at the opposite end of the spa when pushing out the air to ensure that all of the air is removed and your spa cover is properly secured.

Remove the Remaining Air

Step 1: Use the pump to add more air if necessary. If you notice any sagging in the cover, add more air to that area.

Step 2: Check for any remaining air pockets. Use your hands to smooth out any remaining air pockets or wrinkles.

Step 3: Repeat the process. If you still notice air pockets or sagging in the cover, repeat the process until all air is removed and the cover is snug.

Remove Any Remaining Water

Once you have removed all the air from the spa cover, it’s time to check for any remaining water. Water can accumulate on the cover, and if it’s not removed, it can cause damage or mold growth.

To remove any remaining water, use a sponge or a towel to soak up any standing water on the cover. If there is a lot of water, you can use a wet/dry vacuum to remove it. Be sure to get into all the creases and folds of the cover to remove any water that might be trapped there.

After you have removed all the water, let the cover air dry completely before storing it away. If you don’t allow the cover to dry completely, it can also lead to mold or mildew growth.

Remember to clean your spa cover regularly to prevent any build-up of dirt, debris, or water. A clean cover will not only look better but will also last longer.

By following these simple steps, you can safely and easily remove the spa cover, push out the air, and remove any remaining water. With proper care and maintenance, your spa cover will last for years to come.

Step 5: Fold and Store Your Spa

Once you’ve drained and cleaned your inflatable spa, it’s time to fold it up and store it away until your next use. Here are a few tips to help you with this process:

Start with a clean, dry surface: Before you begin folding your spa, make sure the surface is clean and dry. This will prevent any dirt or debris from getting inside the spa during storage.

Follow the manufacturer’s instructions: Every inflatable spa is different, so be sure to follow the manufacturer’s instructions when folding and storing your spa. This will ensure that you don’t damage the spa or compromise its integrity.

Fold carefully: When folding your spa, be sure to do so carefully and evenly. This will help prevent any unnecessary stress on the seams or walls of the spa.

Store in a dry, cool place: Once your spa is folded, store it in a dry, cool place away from direct sunlight. This will help prevent any damage from heat or moisture.

Consider a storage bag: Some inflatable spa models come with storage bags, which can help protect the spa from dust and debris during storage. If your spa didn’t come with a storage bag, you can purchase one separately.

Make Sure It’s Dry

Before you fold and store your spa, it is important to make sure it is completely dry. This will prevent any mold or mildew from growing while it is stored away.

First, use a towel to dry off any remaining water on the surface of the spa. Next, open all of the valves and let any remaining water drain out. You can also use a vacuum or shop vac to suck out any remaining water in the spa.

Once you’ve removed as much water as possible, let the spa sit for a few hours with the valves open to allow any remaining moisture to evaporate. You can also use a fan or dehumidifier to speed up the drying process.

When you’re confident that the spa is completely dry, you can begin folding it up and storing it away until your next use.

Frequently Asked Questions